Heat sensor: PT100 thermistors

If the delta height is good then G33 is nice.

Then M500 to save.

#define TEMP_SENSOR_0 201

#define TEMP_SENSOR_0 0 // this turns off the second PT100 sensor

 E3D Hotendkit

S3D but try a baudrate of 250000. IIRC that’s what I used for Pronterface.

hot end nozzle is v6 yet holder is janky

E3D v6 Mount for DreamMaker OverLord

AFIF

February 17, 2018

Summary

Print:
1 x Body
1 x Body Lock
1 x Fan Duct (for left blower fan)
1 x Fan Duct but mirrored (for right blower fan)
2 x Blower Guard

Screws:
2 M3 screws and 2 nuts to attach the Body and the Body Lock.
2 M3 screws and 2 nuts to attach the Blower Guard to the blower fan.
2 M3 screws (self-tap) to attach the blower fans to each side of the Body.
4 M3 screws are needed to attach the mount to the printer’s carriage.

Blower fans:
5015 24V

For rigidity, print the Body and Body Lock with at least 2-3 perimeters and 20-30% infill. Supports may be needed for the angle overhang of the Body.

Print the Blower Guard with 3 perimeters but without top/bottom layer. Make the infill percentage and pattern to your liking.

Assemble every printed parts together with blower fans and the hotend, but left out the heat sink cooling fan and the bowden tube. Screw the assembled mount to the printer’s carriage. Finally, add the remaining parts.

No need to do another calibration for the bed leveling. Just calibrate your z offset using Pronterface.

Also, the fans are quite loud at full speed. But you do get a lot of air flows!

FYI 1: I printed everything with PLA (I only have PLA at the moment) and everything has been working well so far, except that the right Blower Duct is slightly deform at the end due to the heat from the heater block.

FYI 2: I use E3D hotend (heat sink, heater block everything) from E3D, and not the E3D upgrade parts from DreamMaker. The heater block from DreamMaker seems a bit larger, so your mileage may vary :)

#define PROBE_MANUALLY

#define Z_CLEARANCE_BETWEEN_PROBES 1// 1mm above the glass so you don’t have to press the buttons lots

#define AUTO_BED_LEVELING_BILINEAR

#define RESTORE_LEVELING_AFTER_G28

Stepper

rotation_distance: 40

homing_speed: 50

position_endstop: 297.05

arm_length: 333.0

extruder:

microsteps: 16

rotation_distance: 33.500

heater bed:

sensor_type: EPCOS 100K B57560G104F

nozzle

sensor_type:

printer:

max_velocity: 300

max_accel: 9000

max_z_velocity: 150

---

just finished configuring my new 2.0.8 1 FW

did a rebuild to see everthing is ok

decided on a screen uncommented it and i get an error (below)

anyone knows what it could be?

INPORTANT INFO >

* all libraries are up to date

* 2.0.6 and 1.1.9 compile fine

In file included from sketch\src\lcd\dogm/marlinui_DOGM.h:31:0,

from sketch\src\lcd\marlinui.cpp:126:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:37:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:40:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:53:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:56:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:71:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:81:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:90:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:103:77: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:115:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:118:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:131:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:134:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

from sketch\src\lcd\dogm\lcdprint_u8g.cpp:14:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

from sketch\src\lcd\dogm\marlinui_DOGM.cpp:42:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

from sketch\src\lcd\dogm\dogm_Statusscreen.h:32,

from sketch\src\lcd\dogm\status_screen_DOGM.cpp:32:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: ‘init’ is not a member of ‘U8GLIB’

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function ‘void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)’:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: ‘init’ is not a member of ‘U8GLIB’

U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

^~~~

exit status 1

Error compiling for board Arduino Mega or Mega 2560.